SJ/T 11340-2015 English PDF (SJT11340-2015)

Delivery: 3 seconds. Download true-PDF + Invoice.
Get QUOTATION in 1-minute: Click SJ/T 11340-2015
Historical versions: SJ/T 11340-2015
Preview True-PDF (Reload/Scroll if blank)

SJ/T 11340-2015: General specification for front projector
SJ/T 11340-2015
SJ
ELECTRONIC INDUSTRY STANDARD
OF THE PEOPLE’S REPUBLIC OF CHINA
ICS 33.160.25
M 74
File No.:
Replacing SJ/T 11340-2006
General specification for front projector
ISSUED ON: APRIL 30, 2015
IMPLEMENTED ON: OCTOBER 01, 2015
Issued by: Ministry of Industry and Information Technology of the People's
Republic of China
Table of Contents
Foreword ... 3
1 Scope ... 5
2 Normative references ... 5
3 Terms, definitions and abbreviations ... 6
4 General requirements ... 7
5 Technical requirements ... 8
6 Test methods ... 12
7 Inspection rules ... 14
8 Marks, packaging, transportation, storage ... 21
9 Requirements for preparation of product instruction manual ... 22
Annex A (normative) Unpacking inspection content and criteria for nonconformity . 23
Annex B (normative) Technique assembly inspection content and criteria for
nonconformity ... 27
Annex C (normative) Environmental test content and criteria for nonconformity ... 28
Annex D (normative) Content of inspection for performance at room temperature and
criteria for nonconformity ... 30
Annex E (normative) Contents of product instruction manual ... 31
General specification for front projector
1 Scope
This Specification specifies the function and performance, test methods, inspection
rules, marks, packaging, transportation, storage, etc. for front projectors.
This Specification applies to front projectors with liquid crystal (LCD), liquid crystal
on silicon (LCoS), and digital optical processing (DLP) projection methods. It is the
main basis for product design, production finalization and inspection. Other projection
methods and front projectors used in different occasions can use this Specification as a
reference.
2 Normative references
The following referenced documents are indispensable for the application of this
document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
GB/T 191, Packaging and storage marks
GB/T 2828.1, Sampling procedures for inspection by attributes -- Part 1: Sampling
schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
GB/T 2829, Sampling procedures and tables for periodic inspection by attributes
(apply to inspection of process stability)
GB 4943.1, Audio/video, information and communication technology equipment -
Part 1: Safety requirements
GB 5296.1, Instructions for use of products of consumer interest - Part 1: General
principles
GB/T 5465.2, Graphical symbols for use on electrical equipment - Part 2: Graphical
symbols
GB 9254, Information technology equipment - Radio disturbance characteristics -
Limits and methods of measurement
GB/T 14960, Technical requirements and measurement methods of infrared remote-
control radiation unit for television broadcast receivers
GB 17625.1, Electromagnetic compatibility - Limits - Part 1: Limits for harmonic
current emissions (equipment input current ≤16 A per phase)
SJ/T 10514-1994, Technical requirements and methods of measurement on infrared
remote control unit for television broadcast receivers
SJ/T 10919, Packaging of color broadcasting TV receiver
SJ/T 11324, Terminology of digital television receiving equipment
SJ/T 11325, Reliability test methods for digital television receiver and display
equipment
SJ/T 11326, Environmental testing methods for digital television receiver and
display equipment
SJ/T 11329, Specification of interfaces for digital television receiving equipment.
Part 3: Video interface of composite video blanking synchronization
SJ/T 11330, Specification of interfaces for digital television receiving equipment.
Part 4: Video interface of S-Video
SJ/T 11331, Specification of interfaces for digital television receiving equipment.
Part 5: Analog audio interface
SJ/T 11332, Specification of interfaces for digital television receiving equipment -
Part 6: Analog video interface of RGB
SJ/T 11333, Specification of interfaces for digital television receiving equipment -
Part 7: Interface of video component YPBPR
SJ/T 11346-2015, Methods of measurement for electronic projectors
SJ/T 11348-2016, Methods of performance measurement for flat panel displays
3 Terms, definitions and abbreviations
3.1 Terms and definitions
For the purposes of this document, the terms and definitions defined in SJ/T 11324 as
well as the followings apply.
3.1.1 front projector
A projector that allows users to view projected images normally on the same side as the
projector.
3.1.2 passive standby mode
A low power state in which the projector is connected to mains power and does not
provide primary functionality. The projector can only enter this mode after receiving
external excitation signals such as remote control and buttons. The projector can return
to the working mode from this mode through the excitation of the remote control device,
internal signal, etc.
3.1.3 passive standby power
The active power measured by the projector in passive standby mode.
NOTE: The unit is watts (W).
3.1.4 unit quality
The overall quality of the projector including working lens.
NOTE: The unit is kilograms (kg).
3.1.5 ratio of all white and all black
Under standard working conditions, the ratio of the average illuminance of a full white
field image to a full black field image.
3.2 Abbreviations
The following abbreviations apply to this document.
UQ: Unit Quality.
4 General requirements
4.1 Normal use conditions
Normal use conditions are:
- Ambient temperature: 5°C~ 35°C:
- Relative humidity: 20% ~ 80% (non-condensation state);
- Air pressure: 86 kPa ~ 106 kPa:
- Power supply: AC 176 V~ 240 V, 49 Hz~ 51 Hz.
4.2 Graphical symbols for equipment
Graphical symbols shall comply with the relevant provisions of GB/T 5465.2.
The graphic symbols not defined in GB/T 5465.2 shall be specified by the product
7.1.3.1 Classification for nonconformity
The front projector is divided into safety nonconformity (indicated by the character Z
in Table A.1), type A, type B and type C nonconformity according to the severity of
quality characteristics.
7.1.3.2 Classification for nonconforming products
A unit product with one or more nonconforming items is called a nonconforming
product. According to the nonconforming type, it is divided into safety nonconforming
products, type A nonconforming products, type B nonconforming products, and type C
nonconforming products.
7.1.3.3 Criteria for nonconformity
The criteria for failure are as follows:
a) Requirements for performance at room temperature: According to the provisions
of Annex D.
b) Requirements for appearance, structure: According to A.4 in Annex A.
c) Safety requirements: As long as it does not meet the requirements in 5.8, it will
be judged as safety nonconformity.
d) Requirements for electromagnetic compatibility characteristic limits: According
to the relevant provisions in 5.7.
e) Requirements for environmental adaptability: According to Annex C.
f) Requirements for reliability: According to the relevant provisions in 5.9.
7.1.4 Judgement for conformity and nonconformity
7.1.4.1 Appearance structure
The test results are in accordance with the provisions of A.4 in Annex A. Type Z and
type A nonconforming products are not allowed. The number of nonconforming
products of type B is not more than 3. The numb...