GB 24977-2010 English PDF (GB24977-2010)

Delivery: 3 seconds. Download true-PDF + Invoice.
Get QUOTATION in 1-minute: Click GB 24977-2010
Historical versions: GB 24977-2010
Preview True-PDF (Reload/Scroll if blank)

GB 24977-2010: Bathroom furniture
GB 24977-2010
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 97.140
Y 81
Bathroom furniture
卫浴家具
ISSUED ON: AUGUST 09, 2010
IMPLEMENTED ON: JUNE 01, 2011
Issued by: State Administration for Market Regulation;
Standardization Administration of PRC.
Table of Contents
Foreword ... 3 
1 Scope ... 4 
2 Normative references ... 4 
3 Terms and definitions ... 5 
4 Product categories ... 6 
5 Requirements ... 7 
6 Test method ... 14 
7 Inspection rules ... 20 
8 Marking, packaging, transportation, storage, instruction for use ... 23 
Bathroom furniture
1 Scope
This standard specifies the terms and definitions, product classification,
requirements, test methods, inspection rules and markings, packaging,
transportation, storage, use instructions of bathroom furniture.
This standard applies to the furniture used in toilets and bathrooms. The
furniture used in other similar places can be implemented with reference to this
standard.
2 Normative references
The provisions in following documents become the provisions of this Standard
through reference in this Standard. For the dated references, the subsequent
amendments (excluding corrections) or revisions do not apply to this Standard;
however, parties who reach an agreement based on this Standard are
encouraged to study if the latest versions of these documents are applicable.
For undated references, the latest edition of the referenced document applies.
GB/T 1732 Determination of impact resistance of film
GB/T 2828.1-2003 Sampling procedures for inspection by attributes -Part 1:
Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot
inspection
GB 4706.1-2005 Household and similar electrical appliances – Safety - Part
1: General requirements
GB/T 4893.1 Furniture - Assessment of surface resistance to cold liquids
GB/T 4893.2 Furniture - Assessment of surface resistance to wet heat
GB/T 4893.3 Furniture - Assessment of surface resistance to dry heat
GB/T 4893.4 Test of surface coatings of furniture - Part 4: Determination of
adhesion - Cross cut
GB/T 4893.7 Test of surface coatings of furniture - Part 7: Determination of
surface resistance to alternation of heat and cold
GB/T 4893.8 Test of surface coatings of furniture - Part 8: Determination of
wearability
GB/T 4893.9 Test of surface coatings of furniture - Part 9: Determination of
resistance to impact
GB 5296.6 Instructions for use of products of consumer interest - Part 6:
furniture
GB 6566 Limit for radionuclides in building materials
GB/T 6739-2006 Paints and varnishes - Determination of film hardness by
pencil test
GB/T 10357.1 Test of mechanical properties of furniture - Part 1: Strength
and durability of tables
GB/T 10357.5 Test of mechanical properties of furniture - Part 5: Strength
and durability of storage units
GB/T 13667.1-2003 Specification for steel book shelves
GB/T 17657-1999 Test methods of evaluating the properties of wood-based
panels and surface decorated wood-based panels
GB 18584 Indoor decorating and refurbishing materials - Limit of harmful
substances of wood based furniture
JC 981-2005 Household glass-washbowl and tabletop
QB/T 1102-2006 Civil ornamental mirror
QB 2658-2004 Lavatory for sanitary fittings
QB/T 3814-1999 Surface examination method of the metal deposits and
conversion coatings for the light industrial products
QB/T 3826-1999 Corrosion-resistant testing method of the metal deposits
and conversion coatings for the light industrial products - Neutral salt
spraying test (NSS)
3 Terms and definitions
The following terms and definitions apply to this standard.
3.1
Bathroom furniture
It is a unified term of series of cabinets (stands) and racks in the toilets and
bathrooms that are used to support washbasins and have shelf and storage
5.7 Hygiene and safety requirements (basic items)
5.7.1 The limit of harmful substances in wooden products shall meet the
requirements of GB 18584.
5.7.2 The radioactivity of the product shall meet the grade A requirements in GB
6566.
5.7.3 Parts or accessories that may be touched during normal use shall not
have burrs, sharp ends, sharp edges, or sharp corners.
5.8 Installation and use requirements (basic items)
5.8.1 The components of the product shall be connected firmly and tightly; the
joint shall be flat and free from chipping and loosening.
5.8.2 The installation of various accessories and connectors shall not miss parts
or nails, or have penetrated nail.
5.8.3 After installation, the opening and closing components shall be operated
flexibly.
5.8.4 There shall be no seepage or water leakage under normal use after
installation between all parts of the product.
5.8.5 The cabinet shall be level after installation; the parallelism with the ground
shall not be greater than 0.7‰.
5.8.6 The cabinet installation shall be vertical. All moving parts shall not be self-
opening after being impacted by external forces.
5.8.7 The electrical appliances such as lamps, sockets and switches shall be
installed firmly and grounded reliably.
6 Test method
6.1 Determination of major dimensional deviations, shape and position
tolerances
6.1.1 Determination of major dimensional deviations
The sample shall be placed on a flat plate or flat ground; measured by a steel
ruler or tape measure with an accuracy of not less than 1 mm. The dimensional
deviation is the difference between the product identification value and the
measured value.
6.1.2 Determination of warpage
Make determination according to the requirements of GB/T 4893.1 ~ 4893.4,
GB/T 4893.7 ~ 4893.9, 4.40 of GB/T 17657-1999.
6.4.2.2 Determination of physical and chemical properties of soft and hard
coverings
Make determination according to the requirements of GB/T 4893.1 ~ 4893.3,
GB/T 4893.7, 4.29, 4.38, 4.40 of GB/T 17657-1999.
6.4.2.3 Determination of physical and chemical properties of metal
surface coatings
6.4.2.3.1 Hardness
Make determination according to the requirements of GB/T 6739-2006.
6.4.2.3.2 Impact strength
Make determination according to the requirements of GB/T 1732.
6.4.2.3.3 Corrosion resistance
Make determination according to the requirements of 7.3.3.7 of GB/T 13667.1-
2003.
6.4.2.3.4 Adhesion
Make determination according to the requirements of GB/T 4893.4.
6.4.2.4 Roughness of metal plating layer
Make determination according to the requirements of 3.2 of QB/T 3814-1999.
6.4.2.5 Resistance to salt spray on metal plating
Make determination according to the requirements of QB/T 3826-1999.
6.4.2.6 24h water absorption thickness swelling rate of wooden parts
Make determination according to the requirements of 4.6 in GB/T 17657-1999.
6.4.2.7 Dip peel off of veneer and soft-hard veneer
Make determination according to the requirements of the category II dip peel
off test of clause 4.17 of GB/T 17657-1999.
6.5 Water resistance
As shown in Figure 2, use a 50 ~ 80 hole shower head with a hole diameter of
1.0 mm ~ 1.5 mm and a flow rate of 10 L/min ~ 12 L/min, to sprinkle the
6.7 Hygiene and safety requirements test
6.7.1 The limit test of harmful substances in wooden products shall be
determined in accordance with the provisions of GB 18584.
6.7.2 The product radioactivity test shall be performed in accordance with the
provisions of GB6566.
6.7.3 The safety of parts or accessories shall be inspected ac...